Site Diary › Toolbox talks › Roof work and fragile roofs

Roof work toolbox talk

A roof puts an edge, a slope and a surface that may not hold you all in one place. Clear roof sheets, old fibre-cement sheets, rusted sheeting and ceiling boards can look solid and give way under one step. The Construction Regulations add extra duties for roof work on top of the normal fall protection rules.

  • Work at height
  • About 5 minutes
  • Free PDF with register
Download the PDF Blank register

Two A4 pages: the talk to read out, then an attendance register with 22 numbered rows. Or print this page from your browser.

Say this

Read it out, or put it in your own words. Stop and point at the real thing on this site wherever you can.

1. Plan it before anyone goes up

Roof work must be planned, and our fall protection plan must cover it. Only competent roof erectors work on the roof. Before you go up, know how you will get up and down, where the edges and fragile areas are, and where you will clip on if you need a harness.

2. Fragile means you fall through

Treat these as if they are holes: clear sheets and skylights, old fibre-cement sheets, rusted or thin sheeting, and anything you are not sure of. Never stand or kneel on them, and never step on them to reach something. To work across or near them, use crawl boards, roof ladders or platforms that spread your weight onto the structure, and cover or rail off skylights. If old sheets might contain asbestos, stop and ask before you cut, drill or break them.

3. Guard the edges

At the eaves and gable ends we put up guardrails, barriers and toe-boards wherever it is reasonably practicable, so people, tools and sheets cannot go over. Where that cannot be done, you work in a harness clipped to an approved anchor, as the plan says. The working at heights talk covers harnesses.

4. Watch the weather

Nobody works on a roof in bad weather or when conditions make it dangerous. Rain, dew and dust make sheeting slippery. Wind can catch a roof sheet like a sail and pull you off. If you see lightning or hear thunder, come down at once. In summer, sheeting gets very hot in the midday sun, so take water up and take breaks.

5. Materials on the roof

Tie down bundles of sheets and loose material so the wind cannot lift them. Do not stack anything on fragile sheeting or near the edge. Do not throw off-cuts, screws or old sheets down. Lower them, and keep the area below barricaded so nobody walks underneath.

6. Inside the roof space

In the roof space, step only on the trusses or on boards laid across them. Ceiling boards will not hold your weight, and a foot through the ceiling can mean a fall into the room below.

Check on site today

  • Is roof work in today's fall protection plan, and are the roof erectors competent?
  • Point out every fragile area: skylights, old sheets, rusted sheets, ceiling boards
  • Crawl boards, roof ladders or platforms on hand and in good condition
  • Edge protection at eaves and gables, or approved anchor points for harnesses
  • Wind, rain and storm forecast checked before anyone goes up
  • Area below the roof barricaded and loose material tied down

Ask the crew

Open questions get people talking. Listen to the answers: they tell you what's really happening on site.

  • Which parts of this roof would not hold your weight?
  • How do we get across a fragile area safely?
  • What weather would make you come down?
  • What do we do with off-cuts and old sheets?

Protective equipment for this job

  • Hard hat
  • Safety boots with soft, grippy soles suited to roof sheeting
  • Harness and lanyard where the fall protection plan calls for one
  • Gloves for handling sheeting with sharp edges
  • Sun protection: long sleeves, a brim or neck flap, and water

What the law says

In our own words. Follow the links for the full wording.

  • Construction Regulations, 2014, regulation 10(5): Fall protection, roof workFor roof work the fall protection plan must show that the work is properly planned, the roof erectors are competent, nobody works on the roof in bad weather or other dangerous conditions, covers over openings and fragile material are strong enough, there are suitable platforms or coverings to carry anyone crossing fragile material, and guardrails, barriers and toe-boards stop people, material and equipment falling as far as reasonably practicable.Read on 21 November 2026
  • Construction Regulations, 2014, regulation 10(1) to (4): Fall protectionThe contractor must have a competent person prepare a fall protection plan with a rescue plan, keep it followed, guard unprotected openings and edges, and use fall arrest equipment such as harnesses only where fall prevention is not reasonably practicable.Read on 21 November 2026
  • General Safety Regulations, 1986, regulation 12: Roof workThe employer must provide, and make sure people use, suitable roof ladders, duck-boards or crawling boards for anyone working on a roof that has an unsafe pitch or surface, or that is or will be covered with material a person could fall through. On pitched roofs covered with non-fragile material, safety belts attached to the structure or similar effective equipment may be used instead.Read on 21 November 2026

Sign the register

Everyone who listened signs page 2 of the PDF: name, company or trade, signature. Keep it in the site's health and safety file. How to fill in the register.

This talk is general safety information for South African sites, not legal advice. Your site's risk assessment, safe work procedures and health and safety plan come first. Written 21 November 2026 by Kindly Made from the sources linked above.