Say this
Read it out, or put it in your own words. Stop and point at the real thing on this site wherever you can.
1. Think before you grab
Most hand injuries happen when people reach in without looking. Before you pick something up or put your hand somewhere, ask: can this crush, cut, burn or catch my hand? Where are my fingers going to be when this moves or lands? Keep your hands out of the line of fire.
2. Pinch points and crushing
Fingers get crushed between blocks when stacking, under shutter panels and steel when they are put down, between a load and a wall, and in doors and tailgates of the bakkie. Put loads down on timber spacers so your fingers are not underneath. Use a tag line or push stick instead of your hand to guide loads and material. Never put your hand into a mixer, a compactor or any machine that is running or could start.
3. Cuts and punctures
Sheet metal, cut steel, broken glass, tile edges and utility knives cause deep cuts. Cut away from your body and keep your other hand behind the blade. Bend over or pull out nails sticking out of old timber and shutters. Do not carry glass or sheeting against your body without cut-resistant gloves and help.
4. The right glove for the job
There is no single glove for everything. Leather or heavy work gloves for blocks, steel and rough material. Cut-resistant gloves for sheet metal and glass. Waterproof gloves for cement and wet work. Chemical gloves of the type on the safety data sheet for solvents and acids. Welding gauntlets for welding. A cotton glove soaked in cement or solvent is worse than no glove. Gloves must fit: too big and they catch, too small and you take them off.
5. When not to wear gloves
Do not wear gloves, loose sleeves or rings near rotating parts that can grab them, like a drill press, a bench grinder or a spinning drill chuck. A glove caught in a spinning part pulls the whole hand in. Rings can also catch on edges and tear a finger; take them off at work.
6. Vibration and getting help
Long hours on breakers, compactors, grinders and hammer drills can damage the nerves and blood vessels in your hands. Tingling, numbness or fingers going white, especially in the cold, are warning signs: tell the supervisor and see a clinic. Swap the tool between people and keep hands warm and dry. For any cut, crush or puncture, go to the first aider straight away and report it, however small.
Check on site today
- Which jobs today involve sharp edges, heavy blocks or steel, chemicals, cement or vibrating tools?
- Are the right types of gloves on site for each of those jobs, in sizes that fit the crew?
- Are there nails sticking out of stripped shutters or old timber that need to be removed?
- Are guards fitted on grinders, saws and mixers, and is nobody reaching into running machines?
- Is the breaker or compactor work shared out so nobody uses it all day?
Ask the crew
Open questions get people talking. Listen to the answers: they tell you what's really happening on site.
- Show me your hands: what scars do you have, and how did you get them?
- Which glove do you use for which job on this site, and which job has no good glove?
- Where on this site could your fingers get caught between two things?
- Have you had tingling or numb fingers after using the breaker or grinder?
Protective equipment for this job
- Leather or heavy-duty work gloves for blocks, steel and rough materials
- Cut-resistant gloves for sheet metal, glass and tiles
- Waterproof gloves for cement and wet work
- Chemical-resistant gloves as named on the safety data sheet
- Welding gauntlets for welding and cutting
What the law says
In our own words. Follow the links for the full wording.
- Occupational Health and Safety Act 85 of 1993, section 8: General duties of employers to their employeesSubsection (2)(b): the employer must take reasonably practicable steps to eliminate or reduce a hazard before resorting to personal protective equipment, so gloves come after safer methods, guards and tools.Read on 21 November 2026
- General Safety Regulations, 1986, regulation 2: Personal safety equipment and facilitiesWhere a hazard cannot be made safe, the employer must provide free of charge and maintain suitable protective equipment, which can include gloves and gauntlets, instruct employees in its proper use and limits, and not let anyone work without the required equipment.Read on 21 November 2026
- Physical Agents Regulations, 2024, regulation 13: VibrationThe employer must eliminate hand-arm vibration at the source where reasonably practicable, and where exposure reaches the levels in the regulations must, among other things, use other work methods, choose lower-vibration equipment, maintain it, limit how long people are exposed and provide clothing that protects against cold and damp.Read on 21 November 2026
- Occupational Health and Safety Act 85 of 1993, section 14: General duties of employees at workEmployees must take reasonable care of their own and others' safety, obey the employer's safety rules, and report any injury to the employer or health and safety representative before the end of the shift in which it happened, unless that was not possible.Read on 21 November 2026
Sign the register
Everyone who listened signs page 2 of the PDF: name, company or trade, signature. Keep it in the site's health and safety file. How to fill in the register.
Free from sitediary.co.za/toolbox-talks/hand-safety/. The attendance register is page 2 of the PDF, or sitediary.co.za/toolbox-talks/attendance-register/. General safety information, not legal advice: follow your site's risk assessment and health and safety plan.
This talk is general safety information for South African sites, not legal advice. Your site's risk assessment, safe work procedures and health and safety plan come first. Written 21 November 2026 by Kindly Made from the sources linked above.