Say this
Read it out, or put it in your own words. Stop and point at the real thing on this site wherever you can.
1. Trained on that tool
Only use a grinder, saw or cutter if you have been trained on that type of machine. Your employer must give you the training you need to use it safely. If you have not used this tool before, say so. There is no shame in asking, but there is real danger in pretending.
2. Right disc, right speed
Every disc is marked with its top safe speed. That speed must be at least as high as the speed marked on the grinder. Never fit a bigger disc than the grinder and guard were made for. Use cutting discs for cutting and grinding discs for grinding, and never grind with the side of a thin cutting disc. Check the disc for cracks or chips and fit it with the correct flanges. Unplug the tool or take the battery out before changing a disc.
3. Guards and handles stay on
The guard is there to catch the pieces if a disc bursts. Never take it off, never turn it so it no longer covers you, and never take off the side handle. Saw guards must spring back freely. A guard tied back with wire is a broken tool.
4. Check before you plug in
Look at the lead and plug. Cuts, bare wires, taped joints or a cracked casing mean the tool is out of service: tag it and hand it in. Plug in only where the supply is protected by an earth leakage unit, and keep leads out of water and away from the cutting line.
5. While you cut
Clamp or wedge the work so it cannot move. Hold the tool with both hands and stand firm, to the side of the disc's line, not behind it. Point sparks away from people, gas bottles and anything that can burn. Keep sleeves, cloths and hair away from the spindle. After you switch off, let the disc stop before you put the tool down.
6. Eyes, ears and lungs
Grinding and cutting throw out sparks, chips and dust. Wear eye protection, and a face shield when grinding. Use hearing protection and a dust mask or water suppression when cutting brick, block or concrete. People watching must protect their eyes too.
Check on site today
- Who on the crew is trained on the grinders and saws, and who is not yet?
- Every grinder's guard and side handle fitted and in the right position
- Disc speed ratings match or exceed each grinder's marked speed
- Leads and plugs undamaged, with no taped joints
- Earth leakage protection on the supply used for power tools
- Eye protection and face shields available at every cutting point
Ask the crew
Open questions get people talking. Listen to the answers: they tell you what's really happening on site.
- How do you check that a disc is right for this grinder?
- Why might someone take a guard off, and what can happen if they do?
- Where should you stand when you cut, and why?
- What do you do with a tool that has a damaged lead?
Protective equipment for this job
- Safety glasses or goggles
- Face shield for grinding
- Hearing protection
- Dust mask or respirator when cutting masonry or concrete
- Gloves suited to the job (not loose gloves near a spinning drill bit)
- Safety boots
What the law says
In our own words. Follow the links for the full wording.
- Driven Machinery Regulations, 2015, regulation 9: Grinding machinesFor power-driven grinding machines: the machine must be marked with its rated spindle speed, and no wheel may run faster than its maker allows. Wheels must be mounted properly between suitable flanges, and the machine must have a strong guard enclosing the wheel as far as practicable. There must be a transparent shield, or every operator must be issued with eye protection and wear it, and a notice must warn that nobody may grind, inspect or watch grinding without eye protection. Operators of machinery used for grinding, cutting, fettling, polishing or similar work must be specifically trained for that machinery.Read on 21 November 2026
- Occupational Health and Safety Act 85 of 1993, section 8: General duties of employers to their employeesThe employer must provide and maintain plant, machinery and systems of work that are safe as far as reasonably practicable, remove or reduce hazards before relying on protective equipment, and give the information, instruction, training and supervision workers need.Read on 21 November 2026
- Occupational Health and Safety Act 85 of 1993, section 15: Duty not to interfere with, damage or misuse thingsNobody may deliberately or recklessly interfere with, damage or misuse anything provided for health or safety, such as a guard on a grinder or saw.Read on 21 November 2026
Sign the register
Everyone who listened signs page 2 of the PDF: name, company or trade, signature. Keep it in the site's health and safety file. How to fill in the register.
Free from sitediary.co.za/toolbox-talks/power-tools/. The attendance register is page 2 of the PDF, or sitediary.co.za/toolbox-talks/attendance-register/. General safety information, not legal advice: follow your site's risk assessment and health and safety plan.
This talk is general safety information for South African sites, not legal advice. Your site's risk assessment, safe work procedures and health and safety plan come first. Written 21 November 2026 by Kindly Made from the sources linked above.