Say this
Read it out, or put it in your own words. Stop and point at the real thing on this site wherever you can.
1. You only get two
A tiny chip of steel or concrete, a splash of acid or a speck of cement can damage your eye for life. It happens in a split second, often while you are just watching someone else work. You cannot buy new eyes. Safety glasses cost little and take two seconds to put on.
2. Match the protection to the job
Safety glasses with side protection are the minimum for drilling, chiselling, hammering, nailing and general site work. Grinding and cutting with a disc throw sparks and fragments hard and fast, so wear goggles or glasses with a full face shield over them. For pouring acids, chemicals or mixing cement, wear sealed goggles, because liquid gets round ordinary glasses. For welding and cutting with gas, use a proper welding helmet or goggles with the right dark lens. Never use sunglasses or a normal face shield for welding.
3. Welding flash
Looking at a welding arc, even from a few metres away and only for a moment, can burn the front of your eye. It often only starts hurting hours later, at night, with a gritty, painful, watery feeling. Do not look at the arc. If welding is happening, keep away or stand behind the screen. Where it can be done, the welding area must be screened off to protect the people around it.
4. Look after your glasses
Scratched, dirty or misted glasses make people take them off, and then they protect nothing. Clean them with water and a soft cloth, not your dusty shirt. Keep them in a case or pouch, not loose in a toolbox. If they are scratched or broken, ask for new ones; you should not pay for them. If you wear prescription glasses, ask what will fit over them or whether safety prescription glasses can be arranged.
5. If something gets in an eye
Do not rub it, and do not let anyone dig at it with a matchstick, a knife point or a magnet. For dust or a splash, rinse the eye straight away with plenty of clean running water or the eyewash, then go to the first aider. For a chemical splash, keep rinsing for at least 20 minutes and get medical help. If something is stuck in the eye, do not try to remove it: cover the eye and get medical help. A welding flash also needs medical help.
Check on site today
- Which jobs today involve grinding, cutting, chiselling, nailing, welding, chemicals or cement?
- Does everyone doing those jobs, and everyone working near them, have the right eye protection?
- Are there face shields for the grinders and cut-off saws, and are they clean and undamaged?
- Are welding screens up where welding is happening near other people?
- Is there an eyewash or a supply of clean water near the cutting, mixing and chemical areas?
- Are any glasses scratched, broken or missing? Replace them now.
Ask the crew
Open questions get people talking. Listen to the answers: they tell you what's really happening on site.
- Have you ever had something in your eye at work? What were you doing?
- Why do people take their safety glasses off, and what would help them keep them on?
- Which job on this site do you think is the most dangerous for eyes?
- What would you do if a labourer got a splash of brick acid in the eye?
Protective equipment for this job
- Safety glasses with side protection for general site work
- Goggles for grinding, dust, cement and chemical splashes
- Full face shield over glasses or goggles for grinding and disc cutting
- Welding helmet or gas-welding goggles with the correct filter lens
- Welding screens to protect people nearby
What the law says
In our own words. Follow the links for the full wording.
- General Safety Regulations, 1986, regulation 2: Personal safety equipment and facilitiesWhere a hazard cannot be made safe, the employer must provide free of charge, and keep in good and clean condition, suitable protective equipment, which can include goggles, spectacles, face shields, welding shields and visors. The employer must instruct employees in its proper use and limits, and may not let an employee work without the required equipment.Read on 21 November 2026
- General Safety Regulations, 1986, regulation 9: Welding, flame cutting, soldering and similar operationsWelding or flame cutting may only be done if effective protection is provided and used for the eyes and, where needed, the face, and if the work area is partitioned off where practicable; otherwise others exposed must be warned and given suitable protective equipment.Read on 21 November 2026
- Occupational Health and Safety Act 85 of 1993, section 23: Certain deductions prohibitedAn employer may not deduct from wages, or ask an employee to pay, for anything the Act requires the employer to provide in the interest of health or safety, such as required protective equipment.Read on 21 November 2026
- General Safety Regulations, 1986, regulation 3(8): First aid, emergency equipment and proceduresWhere an employee could get a chemical or biological substance in the eye, the employer must provide an eyewash fountain or similar facility close to where that employee works, and train the employee to use it.Read on 21 November 2026
Sign the register
Everyone who listened signs page 2 of the PDF: name, company or trade, signature. Keep it in the site's health and safety file. How to fill in the register.
Free from sitediary.co.za/toolbox-talks/eye-protection/. The attendance register is page 2 of the PDF, or sitediary.co.za/toolbox-talks/attendance-register/. General safety information, not legal advice: follow your site's risk assessment and health and safety plan.
This talk is general safety information for South African sites, not legal advice. Your site's risk assessment, safe work procedures and health and safety plan come first. Written 21 November 2026 by Kindly Made from the sources linked above.