Say this
Read it out, or put it in your own words. Stop and point at the real thing on this site wherever you can.
1. What counts as hot work
Hot work is any job that makes sparks, flames or heat: arc welding, gas cutting, grinding, brazing, soldering and torching on waterproofing. Sparks travel much further than most people think. They drop through gaps in slabs, roll under doors and land in places you cannot see. A spark can smoulder in timber or insulation for a long time and only burst into flame after everyone has gone home.
2. Before you strike an arc
Get the go-ahead from your supervisor first. Look all around, above and below. Move anything that can burn out of the way, or cover it with a fire blanket. Check what is on the other side of the wall or under the floor. Have a working extinguisher right next to you, and ask a second person to watch for sparks and fire while you work. If the area cannot be made safe, the job waits.
3. Never cut a closed or dirty drum
Do not weld, cut or grind any drum, tank, pipe or container that is closed, or that held fuel, paint, thinners or any other chemical. Heat can make what is left inside explode or give off poison gas. It may only be worked on once a competent person has checked it, cleaned it out and signed in writing that it is safe.
4. Protect yourself and the people near you
Wear the right welding helmet or face shield, leather gloves, an apron or flame-resistant overalls, and boots. Arc flash can burn the eyes of people standing nearby, so put up screens, and if you cannot screen the area, warn people and give them eye protection. Work where fumes can blow away. Welding in a tank, pit or other confined space needs proper ventilation or supplied air. Go through the confined spaces talk before anyone works inside one.
5. Electric welding in wet places
Check that welding leads and the electrode holder are fully insulated and not cracked or taped. In wet or damp places, inside metal tanks, or against big metal structures, the welder must be insulated with boots, gloves or rubber mats, and a trained helper must stay with them the whole time.
6. When you finish
Do not just pack up and leave. Walk the area again, above and below, and look and feel for anything smouldering. Keep watching for a while after the last spark. Warn people about hot metal so nobody grabs it with bare hands.
Check on site today
- Look at today's hot work spots and point out anything that can burn within reach of sparks.
- Check that an extinguisher or fire blanket is next to every welding or cutting job.
- Inspect welding leads, electrode holders and earth clamps for cracks, bare wire and taped joints.
- Check that screens are up wherever other people work near welding.
- Ask whether any drum, tank or pipe is due to be cut, and who has checked it is clean and safe.
- Agree who will act as fire watch during the job and check the area after it.
Ask the crew
Open questions get people talking. Listen to the answers: they tell you what's really happening on site.
- Where could sparks from today's job land that we cannot see from where the welder stands?
- What would you do if you were asked to cut open an old drum on site?
- Has anyone had arc eye or a burn from hot work? What happened?
- Who checks the area once the welding is finished, and how long do they watch it?
Protective equipment for this job
- Welding helmet with the correct filter shade for the process
- Safety goggles or a full face shield for grinding and cutting
- Leather welding gloves and a leather apron or flame-resistant overalls
- Safety boots, and insulating boots, gloves or mats for electric welding in wet places
- Respiratory protection where fumes cannot be removed by ventilation
What the law says
In our own words. Follow the links for the full wording.
- General Safety Regulations, 1986, regulation 9: Welding, flame cutting, soldering and similar operationsWelding and flame cutting may only be done by someone fully instructed in the equipment and its hazards, with effective protection for the eyes, lungs and, where needed, the face, hands, feet and body, and with insulated leads and electrode holders. The work must be screened off where practicable; where it is not, other people exposed must be warned and given protective equipment. Confined spaces need ventilation or supplied air. Electric welding in wet places, inside metal vessels or against large masses of metal needs sound insulation, an insulated welder and a trained helper in attendance (unless the voltage to earth is 50 V or less). Closed containers, or ones holding something that heat could ignite or turn poisonous, may not be welded, cut or ground until a competent person certifies them safe in writing. Hot work away from a designated area needs proper fire precautions.Read on 21 November 2026
- Construction Regulations, 2014, regulation 29: Fire precautions on construction sitesAmong other fire duties, the contractor must make sure that welding, flame cutting and other hot work are only done after suitable precautions have been taken to reduce the risk of fire, and that combustible material does not build up on site.Read on 21 November 2026
- General Safety Regulations, 1986, regulation 2: Personal safety equipment and facilitiesWhere a hazard cannot be made safe, the employer must provide suitable protective equipment free of charge, such as welding shields, gloves, aprons and flame-proof clothing, keep it in good condition, show workers how to use it, and not let them work without it.Read on 21 November 2026
Sign the register
Everyone who listened signs page 2 of the PDF: name, company or trade, signature. Keep it in the site's health and safety file. How to fill in the register.
Free from sitediary.co.za/toolbox-talks/hot-work/. The attendance register is page 2 of the PDF, or sitediary.co.za/toolbox-talks/attendance-register/. General safety information, not legal advice: follow your site's risk assessment and health and safety plan.
This talk is general safety information for South African sites, not legal advice. Your site's risk assessment, safe work procedures and health and safety plan come first. Written 21 November 2026 by Kindly Made from the sources linked above.